MECHANICAL

KANNUR UNIVERSITY FACULTY OF ENGINEERING

Curricula, Scheme of Examinations & Syllabi for

B.Tech Degree Programme (III-IV Semesters) in

MECHANICAL ENGINEERING

With effect from 2007 Admissions

THIRD SEMESTER

2K6ME 301 : ENGINEERING MATHEMATICS II
3 hours lecture and 1 hour tutorial per week
Module I:
Infinite Series: Convergence and divergence of infinite series – Ratio test – Comparison test – Raabe’s
test – Root test – Series of positive and negative terms- absolute convergence – Test for alternating
series. Power Series: Interval of convergence – Taylors and Maclaurins series representation of functions –
Leibnitz formula for the derivative of the product of two functions – use of Leibnitz formula in the Taylor
and Maclaurin expansions
Module II:
Matrices: Concept of rank of a matrix –echelon and normal forms – System of linear equation -
consistency – Gauss elimination– Homogeneous liner equations-Fundamental system of solutions- Inverse
of a matrix – solution of a system of equations using matrix inversion – eigen values and eigen vectors -
Cayley- Hamilton Theorem.
Module III:
Vector Integral Calculus: Evaluation of line integral, surface integral and volume integrals – Line
integrals independent of the path, conservative force fields, scalar potential- Green’s theorem- Gauss’
divergence theorem- Stoke’s theorem (proof of these not required).
Module IV:
Vector Spaces: subspaces–linear dependence and independence–bases and dimension-linear
transformations -sums, products and inverse of linear transformations.
References:
1. Kreyszing E. Advanced Engineering Mathematics, Wiley Eastern
2. Sastri. S. S. Engineering Mathematics, Prentice Hall of India.
3. Wylie .C. R. Advanced Engineering Mathematics, Mc Grawhill.
4. B .S. Grewal. Higher Engineering Mathematics, Khanna Publishers.
5. Greenberg. M.D. Advanced Engineering Mathematics, Pearson Education Asia.
6. Narayanan .S. Manickavachagom Pella and Ramaiah. Advanced Mathematics for Engineering
Students, S. Viswanathan Publishers
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6ME 302 : COMPUTER PROGRAMMING
3 hours lecture and 1 hour tutorial per week
Module I (15 hours)
Overview of C – Variables, Expressions and assignments, Lexical Elements, Fundamental Data Types,
Operators Control Statements – if, switch-case, for , while, do, goto, break, switch Functions- Parameter
passing , scope rules, recursion
Module II (12 hours)
Arrays – One dimensional and Multi Dimensional, Pointer-Linked List, Arrays of Pointers, Dynamic
Memory Allocations, Strings – Operations and functions , Bitwise Operators and Enumeration Types ,
Structures and Unions, Files and File Operations
Module III (13 hours)
Overview of Java Language- Constants, Variables and Data Types, Operators and Expressions Control
Structures – Decision Making, Branching and Looping, Object Oriented Programming – Concept of
Classes, Objects and Methods, Benefits Java and OOP- Polymorphism and Overriding of methods,
Inheritance
Module IV (12 hours)
Arrays and Strings, Interfaces, Multiple Inheritance, Packages – Putting Classes together – Managing
Errors and Exceptions – Applet Programming and Graphics Programming (Basics only) – Managing
Input/Output Files in Java
Text books
1. Kelley, Al & Pohl, Ira.,., A Book on C- Programming in C, 4th Ed,, Pearson Education (Modules I &II)
2. Balagurusamy E., Programming with Java: A Primer, 3rd Ed., Tata McGraw-Hill (Module III &IV)
Reference books
1. Balagurusamy E., Programming in ANSI C, Tata McGraw Hill
2. Eckel, Bruce., Thinking in Java, 2nd Ed, Pearson Education
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 303 MECHANICS OF SOLIDS
3 hours lecture and 1 hour tutorial per week
Module I (13 hours)
Introduction - general concepts - definition of stress - stress tensor - stress analysis of axially loaded
members - strength design of members - axial strains and deformations in bars - stress-strain relationships -
Poisson's ratio - thermal strain - Saint Venant's principle - elastic strain energy for uniaxial stress - statically
indeterminate systems - generalised Hooke's law for isotropic materials - relationships between elastic
constants - introduction to anisotropy – orthotropy
Module II (13 hours)
Torsion - torsion of circular elastic bars - statically indeterminate problems - torsion of inelastic circular
bars - axial force, shear force and bending moment - diagrammatic conventions for supports and loading,
axial force, shear force and bending moment diagrams - shear force and bending moments by integration
and by singularity functions
Module III (13 hours)
Bending stresses in beams - bending stresses in beams - shear flow - shearing stress formulae for beams -
inelastic bending of beams - deflection of beams - direct integration method - singularity functions -
superposition techniques - moment area method - conjugate beam ideas - elementary treatment of statically
indeterminate beams - fixed and continuous beams
Module IV (13 hours)
Transformation of stresses and strains (two-dimensional case only) - equations of transformation - principal
stresses - mohr's circles of stress and strain - strain rosettes - compound stresses - superposition and its
limitations - eccentrically loaded members - columns - theory of columns - buckling theory - Euler's
formula - effect of end conditions - eccentric loads and secant formula
Text book
1. Popov E.P., Engineering Mechanics of Solids, Prentice Hall of India
Reference books
1. Timoshenko S.P. & Young D.H., Elements of strength of materials, McGraw Hill
2. Shames I.H., Introduction to Solid Mechanics, Prentice Hall of India
3. Crandall S.H., Dahl N.C. & Lardner T.J., Introduction to Mechanics of Solids, McGraw Hill
4. Beer F.P. & Johnston E.R., Mechanics of Materials, McGraw Hill
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 304 ELECTRICAL MACHINES
3 hours lecture and 1 hour tutorial per week
Module I (12 hours)
DC Generators EMF equation - Armature reaction - Power flow diagram voltage build up- Internal and
external characteristics - Control of terminal voltage
DC Motors: Back EMF - Torque and speed equations- Power flow diagram- Losses - componentsefficiency-
Performance characteristics - Starting method using 3 point starter- Speed control.
Module II (14 hours) .
Transformers: Ideal and real transformer - Equivalent circuit - Phasor diagram - Losses - efficiency and
regulation - All day efficiency - OC and SC tests- Auto transformers - Voltage and current relationships -
Saving of copper - Three phase transformers- Star and Delta connections .
3 phase induction motors -Production of torque - slip and frequency of rotor current - torque slip
characteristics- no-load and blocked rotor tests- equivalent circuit -losses and power flow.
Module III (13 hours)
Starting methods for three phase induction motors - direct on line starting - auto transformer starting - star
delta starting - rotor resistance starting
Alternators - Voltage regulation – predetermination - EMF method - MMF method - Synchronizing with
3 phase mains
Control of Permanent magnet stepper motors
Module IV (13 hours)
Electrical drives: advantages of electrical drives - parts of electrical. drives - choice of electric drives -
status of DC and AC drives - dynamics of electric drives' - fundamental torque equations - multiquadrant
operation - equivalent values of drive parameters - components of load torque - nature and
classification of load torque.
Electrical drives: power semiconductor device- SCR - symbol and characteristics - input-output
characteristic of AC to DC,. AC to AC and DC to DC converters (no derivation) - three phase induction
motor drives- stator voltage control and slip power recovery scheme.
Text books
1. A Text Book of Electrical Technology- B.L. Thereja, A.K.Thereja for Module 1-3
2. Dubey et.al , Thyristorised power controllers, Narosa publications. for Module 4
Reference books
1. Nagarath I. J. & Kothari. D. P.; Electric Machines, Tata McGraw Hill
2. Stephen J Chapman, Electric Machinery Fundamentals, McGraw Hill.
3. Tara V.D., Electrical Machines & Power Systems, Prentice Hall.
4. Fitzgerald A.E. & Kingsley, Electrical ¥achinery, McGraw Hill.
5. Puchestein, Lloyd & Cenrad, Alternatirig Current Machines, Asia Publishing House.
6. Vincent Del Toro, Electrical Machines and Power Systems, Prentice Hall
7. M.D and Kanchandani K.B., Power Electronics, Tata Mc Graw Hill.
8.Electric Drives – N.K.De and P.K. Sen , Prentice Hall of India.
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 305 FLUID MECHANICS
3 hours lecture and 1 hour tutorial per week
Module 1(15 hrs)
Introduction and basic concepts-distinction between fluids and solids – Application areas of fluid
mechanics-Classification of fluid flows-system and control volume. Properties of fluids-Continuum-density
and specific gravity-vapour pressure and cavitation-viscosity-surface tension and capillary effects -Pressure
-Variation of pressure in a stationary fluid- Manometers.
Fluid static-hydrostatic forces on submerged plane and curved surfaces-Buoyancy and stability.
Fluid kinematics-Lagrangian and Eulerian descriptions-Fundamentals of flow visualization-stream lines,
stream tubes, path tubes, streak lines. Types of motion -deformation of fluid elements-vorticity and
rotationality-Reynolds transport theorem.
Module 2 (14 hrs)
Mass, Bernoullis and Energy equations-Static, Dynamic and Stagnation Pressures-limitation on
the use of Bernoulli equation-Hydraulic grade line and Energy grade line-Applications of Bernoulli
equation-Flow rate and velocity measurements-Pitot tube and Pitot static probes- Obstruction flow meters-
Orifice, Venturi and Nozzle meters-Flow in Pipes- Laminar and turbulent flows- Hagen-Poiseuille
equation-Darcy-Weisbach equation-Minor losses-Moody’s Chart
Module 3 (12 hrs)
Differential analysis of fluid flow-Conservation of Mass-Derivation of continuity equation- stream
function-irrotationality-velocity potential- relationship between stream function and velocity potential in
irrotational flows- Conservation of linear momentum- Navier-Stokes equation-Newtonian versus non
Newtonian fluids- exact solution of continuity and Navier-Stokes equation. Introduction to Computational
Fluid Dynamics.
Module 4 (11 hrs)
Introduction to boundary layer-The boundary layer approximation-boundary layer equations- displacement
thickness- momentum thickness-Blasius solution for flow over a flat plate-Momentum integral equation-
Flow over bodies- Drag and Lift- Drag and lift coefficients- Friction and pressure drag-Flow separation.
Text book
1. Fluid Mechanics- Yunus A Cengel and John M Cimbala, McGraw Hill
Reference books
1. Fluid Mechanics- White F.M, McGraw Hill
2. Fluid Mechanics- Shames I.H, McGraw Hill
3. Fluid Mechanics and its applications- Gupta V. and Gupta S., Wiley Eastern
4. Introduction to Fluid Mechanics- Fox and Mc Donald- John Wiley and Sons
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 306 : METALLURGY AND MATERIAL SCIENCE
( 3 Hours Lecture and 1 Hour Tutorial per week)
Module 1(10Hours)
Classification of materials-Properties of Engineering Materials –structure of atoms and molecules –
Chemical bonds-primary and secondary or molecular bonds- Bond energy and Activation energy-Crystal
structure –Bravai’s lattices –BCC,FCC and CPH structures –Atomic packing factor-Miller indices-
Interplaner spacing –Xray diffraction –Metallographic-Specimen preparation¿ –metallurgical ,scanning
electron microscopes-grain size measurement-etching common etchants used
ModuleII (15Hours)
Defects and Imperfections in crystals –Point defect ,line defects, edge dis location screw dislocationinteraction
of dislocations-Frank reed sources –surface imperfections-Diffusion mechanisms-Fick’s Laws
of diffusion –mechanical behaviour-Elastic ,anelastic and visco elastic materials-plastic deformation
mechanisms-slip –twinning-strengthening mechanisms –phases-solid solutions and compounds-Humerothery
rules-freezing of pure metal-Homogeneous nucleation –Heterogeneous nucleation-crystal growthcast
metal structure
Module III (15 Hours)
Phase diagrams –cooling curves-types equilibrium diagrams-phase diagrams of Cu-Ni ,Bi-Cd ,Pb-Sn; and
Fe-C-Important reactions –pertaining to phase diagrams. Liver Rule
Heat treatment of carbon steels-annealing ,normalizing ,hardening ,tempering, austempering and
martempering –Hardenability and Jomini test-case hardening surface hardening –metallic coating and
surface treatments –failure of material –Creep-Creep resistant materials-fracture-brittle and ductile fracture
–protection against fracture –fatigue –fatigue mechanisms-Sn curves
Module IV (12Hours)
Steels-high alloy steels- tool steels-stainless steels- uses of steels
Cast iron –classifications- structure –applications
Copper alloys and their uses
Aluminium alloys and their uses
Materials with medical applications
Ceramic materials –classification and their uses composites and glasses
Text Book:
1. R.K. Rajput, Material Ssience and Engineering, S.K. Khataria and sons
Reference books-
1. Shackle Ford .JF.,Material science for Engineers –Prentice hall
2. Narang.B.S .,Material Science & Processes –-CBS Publishers
3. Van Vlack L.H., Elements of Material Science -Addison-Wesley.
4. M G K Narula ., Material Science--Tata Mc Grow Hill
5. Prof. Kodgire ., Material Science& Metallurgy –-Everest publications
6. Higgins R.A., Engineering Matellurgy Part I., ELBS
7. Raghavan B., Material Science and Engineering, Prentice Hall India.
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 307(P) : FLUID MECHANICS AND MACHINERY LAB
3 hours Practical per week
Study of plumbing tools and pipe fittings - measurement of meta centric height and radius of gyration of
floating bodies - measurement of viscosity of fluids - study of discharge measuring instruments -
measurement of pressure and velocity
Calibration of venturi meter - orifice meter - notches and weirs - nozzle meters & Rota meters - pipe
friction - minor losses in pipes - verification of Bernoulli’s theorem - demonstration of laminar and
turbulent flow in pipes - critical velocity - forces on curved and plane surfaces
Evaluation of the performance of turbines - main and operating characteristics - Muschel’s curves -
performance of pumping and other machinery like centrifugal pumps - reciprocating pumps - gear pumps -
hydraulic ram and torque
Sessional work assessment
Lab Practicals and Record = 30
Test = 20
Total marks = 50
University evaluation will be for 100 marks of which 70 marks are allotted for writing the
procedure/formulae/sample calculation details, preparing the circuit diagram/algorithm/flow chart, conduct
of experiment, tabulation, plotting of required graphs, results, inference etc., as per the requirement of the
lab experiments, 20 marks for the viva-voce and 10 marks for the lab record.
Note: Duly certified lab record must be submitted at the time of examination
2K6 ME 308(P) : STRENGTH OF MATERIALS LAB
3 hours Practical per week
1. Standard tension test on mild steel using Universal Testing Machine and suitable extensometers
2. Stress - strain characteristics of brittle materials - cast iron
3. Double shear test on mild steel specimens
4. Torsion test on mild steel/brass specimens
5. Spring test - open and closed coiled springs - determination of spring stiffness and modulus of rigidity
6. Determination of modulus of rigidity of wires
7. Impact test - Izod and Charpy
8. Hardness tests - Brinnell hardness, Rockwell hardness (B S C scales), Rockwell superficial hardness
(N & T scales) & Vickers hardness
9. Bending test on beams
10. Fatigue testing - study of testing machine
11. Photo elastic method of stress measurements (two dimensional problems)
Sessional work assessment
Lab practicals & record = 30
Test = 20
Total marks = 50
University evaluation will be for 100 marks of which 70 marks are allotted for writing the
procedure/formulae/sample calculation details, preparing the circuit diagram/algorithm/flow chart, conduct
of experiment, tabulation, plotting of required graphs, results, inference etc., as per the requirement of the
lab experiments, 20 marks for the viva-voce and 10 marks for the lab record.
Note: Duly certified lab record must be submitted at the time of examination
2K6ME 401 : ENGINEERING MATHEMATICS III
3 hours lecture and 1 hour tutorial per week
Module I: (13 hours)
Complex analytic functions and conformal mapping: Complex functions – limits. derivative, analytic
function- Cauchy-Riemann equations- elementary complex functions such as powers, exponential
function, logarithmic, trigonometric and hyperbolic functions- Conformal mapping – Linear
fractional transformations- mapping by elementary functions
Module II: (13 hours)
Complex integration: Line integral, Cauchy’s integral theorem - Cauchy’s integral formula – Taylor’s
series, Laurent series – residue theorem – evaluation of real integrals using integration around unit
circle, around semicircle, integrating contours having poles on the real axis
Module III: (13 hours)
Jointly Distributed Random Variables: Joint distribution functions, independent random variables ,
covariance and variance of sums of random variables, joint probability distribution functions of
random variables, conditional probability and conditional expectations. Curve fitting: Method of least
squares, correlation and regression, line of regression.
Module IV: (13 hours)
Vibrating strings: One dimensional wave equation – D’ Alembert’s solution – solution by method of
separation of variables One dimensional heat equation - solution of the equation by the method of
separation of variable Solutions of Laplace’s equation over a rectangular region and a circular region by
the method of separation of variable
Reference books
1. Kreyszig E. Advanced Engineering Mathematics. Wiley Eastern
2. Johnson, Miller and Freud. Probability and Statistics for Engineers, Pearson Education Asia.
3. Wylie .C.R. Advanced Engineering Mathematics, Mc Grawhill.
4. B.S. Grewal. Higher Engineering Mathematics, Khanna Publishers.
5. Freund. J.E. Mathematical Statistics, Prentice hall of India.
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6ME 402 : HUMANITIES
3 hours lecture and 1 hour tutorial per week
Module I (20 hours)
Functional English Grammar: Sentence Analysis -Basic Patterns -Noun Group, Verbal Group, and
Adverbial Group- Tenses – Conditionals - Active and Passive Voice - Reported Speech
Module II (14 hours)
Technical Communication
1. Nature, Growing need, and importance of technical communication – technical communication skills –
listening, speaking, reading, and writing.
2. Barriers to effective communication – improper encoding, bypassing inter- cultural differences etc.
3. Organization in technical communication – spatial, chronological etc.
4. Style in technical communication - objectivity, accuracy, brevity, clarity etc.
5. Technical reports – types and format
Professional Ethics: 1. Ethics in Engineering, copyright – IPR- patents
Module III (10 hours)
Humanities, Science and Technology
1. Importance of humanities to technology, Education and Society
2. Relevance of a scientific temper
3. Relation between science, society and culture – the views of modern thinkers
4. The development of science and technology in society – science and technology in ancient Greece and
India – the contribution of the Arabs to science and technology – recent advances in Indian science.
Reference books
1. Huddleston R, English Grammar – An outline, Cambridge University Press
2. Pennyor, Grammar Practice Activities, Cambridge University Press
3. Murphy, Intermediate English Grammar, Cambridge University Press
4. Hashemi, Intermediate English Grammar, Supplementary Exercises with answers, Cambridge
University Press
5. Vesilind; Engineering, Ethics and the Environment, Cambridge University Press
6. Larson E; History of Inventions, Thompson Press India Ltd.
7. Bernal J. D., Science in History, Penguin Books Ltd.
8. Dampier W. C., History of Science, Cambridge University Press
9. Encyclopedia Britannica, History of Science, History of Technology
10. Subrayappa; History of Science in India, National Academy of Science, India
11. Brownoski J, Science and Human Values, Harper and Row
12. Schrödinger, Nature and Greeks and Science and Humanism, Cambridge University Press
13. Bossel. H., Earth at a Crossroads – paths to a sustainable future, Cambridge University Press
14. McCarthy, English Vocabulary in Use, Cambridge University Press
15. M. Ashraf Rizvi, Effective Technical Communication, Tata McGraw Hill, New Delhi, 2005
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 10 short type questions of 2 marks, from Module 1
Q II - 10 questions of 5 marks, from module II and III for writing short notes with choice to answer
any seven
Q III - 2 questions A and B of 15 marks from module I for writing essay with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module II for writing essay with choice to answer any one
Q V - 2 questions A and B of 15 marks from module III for writing essay with choice to answer any one
2K6 ME 403 THERMODYNAMICS
( 3 Hours Lecture and 1 Hour Tutorial per week)
Module I (13hours)
Thermodynamics systems-Description of systems –properties-states, processes and cycles- Thermodynamic
equilibrium-forms of energy-equations of state for gasses-compressibility factor –VT,PV,PT, Diagrams
pure substances, properties of steam-Temperature and Zeroth law of thermodynamics –Various temperature
scale –Temperature measuring instruments
Module II (13 Hours)
First law of thermodynamics –concept of heat and work-First law applied to cyclic processes and Noncyclic
processes-definition of stored energy –open system –general and steady flow-application of first law
assess performance
Module III (13hours)
Second law of thermodynamics –thermal energy reservoirs-Kelvin –Planck and Clausius statements and
their equivalence-Reversible and Irreversible processes-Reversible cycle-Carnot corollariesthermodynamic
temperature scale –Clausius inequality –concept of entropy-calculation of entropy changes
from the Tds equations –availability –reversible work and irreversibility –increase of entropy principle-
Helmholtz and Gibbs functions
Module IV (13 hours )
Thermodynamic property relations- Maxwells equations- Clapeyron equation –general relations for internal
energy , enthalpy and entropy in terms of p,v,T and specific heats- the Joule Thomson coefficient h , u
and s of real gases- mixtures of gases-analysis –Gibbs-Dallton model- Properties gas mixtures based on
Dalton model
Text Book:-
Zemansky .M.W ,Thermodynamics,Mc Graw Hill
Reference Books:-
1) Cengel.Y.A & Boles .M .A, Thermodynamics- An Engineering Approch , Mc Graw Hill
2) Jones .I. B & Dugan .R.E Engineering Thermodynamics, Prentice Hall
3) P K Nag , Engineering Thermodynamics ,Tata Mc Graw Hill
4) J.P Holman –Thermodynamics Mc Graw Hill
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 404 MANUFACTURING PROCESSES
3 hours lecture and 1 hour tutorial per week
Module I: Conventional machining operations (12 hours)
Single point tools – center lathe – lathe operations – Boring – Shaping – Planing – Milling- drilling –
grinding – abrasive wheels – centerless grinding – tool materials – machinability
Module II: Non-conventional machining operations ( 14 hours)
High speed machining – hard machining – high speed grinding – creep feed grinding – low-stress grinding
– water-jet machining – abrasive jet machining – chemical machining – electrochemical machining –
electric discharge machining – laser beam machining – electron beam machining – electrolytic grinding –
plasma arc cutting – applications
Module III: Metal fabrication techniques (12 hours)
Forming operations – forging – rolling – extrusion- drawing – casting – sand casting – die casting –
investment casting – continuous casting – miscellaneous techniques – powder metallurgy – welding –
thermal processing of metals – annealing processes – Normalizing – Spheroidizing
Module IV: Manufacturing processes of non-metals (14 hours )
Fabrication and processing of ceramics – glass forming – heat treating glasses- fabrication and processing
of clay products – hydro plastic forming – slip casting – powder pressing – tape casting – processing of
polymers – compression and transfer molding – injection molding – extrusion – blow molding – casting –
drawing – processing of composites.
Text Books
1. G Boothroyd,Winston A Knight - “Fundamentals of machining and machine tools” CRC Press,Taylor
& Francis Group.
2. Milton C Shaw “Metal cutting principles” , Oxford University Press,2005.
3. Callister Jr, William D “Material Science and Engineering – An Introduction “
Wiley India Pvt Ltd.
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6ME 405 : FLUID MACHINERY
3 hours lecture and 1 hour tutorial per week
Module I (13 hrs.)
Classification of fluid machines, stage, stator, rotor- Cylindrical co-ordinate system- integral form of
continuity, momentum and energy equations,Concept of relative velocity,velocity vector equation, velocity
triangle- Performance indices like power and efficiency, Flow of fluid over flat plate and curved
surfaces,fixed and moving,propulsion of ships, rockets and missiles.
Dimensional analysis: Rayleigh’s method and Buckingham’s pi theorem-Principles of modeling and
similitude as applied to fluid mechanics problems.
Module II (13 hrs.)
Hydraulic Turbine: Hydro-electric power plant, components, surge tank fore bay, Classification of turbines
on various criteria, Pelton turbine, work and efficiency, conditions for optimum performance, Francis and
Kaplan turbine components, Euler’s turbine equation, work done and efficiency, Draft tube theory, function
and efficiency, Cavitation in turbine, turbine setting, Model testing, Derivation of dimensionless numbers,
Specific and unit quantities, specific speed, Testing of turbine, characteristic curves, selection criteria,
Governing of turbine. .
MODULE III(13 hrs.)
Rotodynamic pumps: whirling of fluid, vortex motion-free and forced vortex, spiral flow, features of
rotodynamic and positive displacement pumps .Centrifugal Pump: Working Principle, Classification of
centrifugal pump, Volute pump,Turbine pump, Heads, work done by impeller, efficiencies , Pressure rise in
impeller, pressure recovery, Head-discharge curve, effect of various losses, Comparison of forward, radial
and backward curved blades, surging, Priming of Pump, Cavitation and separation in pump. Model
analysis, specific speed, characteristic curves, slurry pump, deep well pump.
MODULE IV(13 hrs.)
Reciprocating Pump: Working principle, single and double acting pump, piston and plunger pumps,
multicylinder pumps, Duplex and Triplex pumps. Indicator diagram, effect of acceleration and friction,
work done, efficiency, slip, function of air vessel, work saved by fitting air vessel, separation in
reciprocating pump, comparison with centrifugal pump.working principle of axial and radial piston
pumps,vane pump and gear pump.
Hydraulic Systems: Jet pump, airlift pump, hydraulic ram, Fluid coupling, working principle, torque
converter, working principle, Hydraulic accumulator, pressure intensifier, hydraulic press, crane, jack.
REFERENCES:
1. Jagadish Lal ,Hydraulic machines.
2. Bansal,R.K , Fluid mechanics and hydraulic machines, Laxmi Publications.
3. J.F.Douglas, J.M.Gasiorek and J.A.Swaffield, Fluid Mechanics, Addison-Wesley, 1995.
4. B.S.Massey, Mechanics of Fluids, Van Nostrand Reinhold.
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 406:MACHINE DRAWING
( 1Hour Lecture and 3 Hours Drawing per week)
Module I (8hours) (Two drawing exercises)
Introduction to machine drawing –principles of orthographic projections applied to machine drawing –
first angle projection and third angle projection-methods of dimensioning –conversion of pictorial
projections in to orthographic projections –sectional views-rules and conventions of sectioning –full
sectional, half sectional ,partial sectional and revolved sectional views of simple machine parts –welded
joints –types of welds –nomenclature of welds –welding symbols drawing of welded machine parts with
details of welding –screwed fastenings- screw thread forms –V and square threads –nomenclature of
threads – conventional representation of threads –hexagonal and square threaded bolt and nuts –locking
arrangements of nuts –various types of machine screws and set screws –foundation bolts –hook bolt- split
bolt –bolt with square plate –rag bolt and Lewis foundation bolt
Module II (16 Hours) (five drawing exercises )
Shaft joints-cotter and pin joints-socket and spigot joint –gib and cotter joint-sleeve and cotter joint-and
knuckle joint Couplings- muff couplings , flanged couplings ,flexible couplings ,Oldham’s coupling and
universal coupling –Parallel and tapered sunk keys –hollow flat saddle keys –feather key and pin key
Bearings –solid journal bearing –bush bearing s –Plummer block –foot step bearing and pedestal bearing –
bracket and hangers –rolling contact bearings –ball bearings –roller bearings and thrust bearings
Pipe joints –coupler joint-union joint-nipple joint –integral and screwed flanged joints
Module III (20 hours) (six drawing exercises)
Assembly drawings – types –accepted norms –engine parts –piston –connecting rod –eccentric –stuffing
box and cross head –Parts of a lathe – tail stock –head stock assembly-tool post and carriage –valves-stop
valves-safety valves-check valves-pressure relief valves and flow direction control valves –miscellaneous
assemblies-vices-screw jack –jigs and fixtures and assembly of pumps
Module IV (8 hours ) (Two drawing exercises)
Limit ,fits and tolerances-nomenclature –classification of fits –systems of fits and tolerances –designationselection
of fits and tolerances
Surface texture-nomenclature of surface texture-designation of surface texture –selection of surface
characteristics-indication of surface roughness-Working drawings of simple machine elements-computer
aided drafting –elements of computer aided drafting –simple exercises using Auto CAD
Reference Books :-
1) Machine drawing by P.I.Varghese & K.C.John, VIP Publishers
2) Machine Drawing by N.D. Butt Panchal
3) Machine Drawing P S Gill S.K.Kataria & sons
4) Machine Drawing by Narayana. K I,Kannaiah& Reddy. K.V
5) Machine Drawing by Narayana. V. I Mathur .M.C .,Jain brothers
Sessional work assessment
Assignments 2x10 = 20
2 tests 2x15 = 30
Total marks = 50
University examination pattern
Q I - 8 short type questions of 5 marks, 2 from each module
Q II - 2 questions A and B of 15 marks from module I with choice to answer any one
Q III - 2 questions A and B of 15 marks from module II with choice to answer any one
Q IV - 2 questions A and B of 15 marks from module III with choice to answer any one
Q V - 2 questions A and B of 15 marks from module IV with choice to answer any one
2K6 ME 407(P) : PRODUCTION ENGINEERING LAB I
3 hours Practical per week
Classifications of machine tools and machining processes - specification of machine tool; power source;
centre lathe - general features, parts and functions - machining on centre lathe - cutting tools - materials,
types, grinding; cutting variables - selection of speeds, feeds and depth of cut - use of cutting fluids -
methods of holding work - lathe operations - turning, thread cutting, drilling, boring, reaming, profile
turning, knurling; tolerance and surface finish - CNC machine tools
Exercises
Jobs on centre lathe requiring simple turning, taper turning, knurling, boring and thread cutting
Sessional work assessment
Lab Practicals and Record = 30
Test = 20
Total marks = 50
University evaluation will be for 100 marks of which 70 marks are allotted for writing the
procedure/formulae/sample calculation details, preparing the circuit diagram/algorithm/flow chart, conduct
of experiment, tabulation, plotting of required graphs, results, inference etc., as per the requirement of the
lab experiments, 20 marks for the viva-voce and 10 marks for the lab record.
Note: Duly certified lab record must be submitted at the time of examination
2K6 ME 408(P) : ELECTRICAL ENGINEERING LAB
3 hours practical per week
1. a) Determination of voltage-current relation of a linear resistance and incandescent lamp
b) measurement of high and low resistance using voltmeter and ammeter
2. R, L and C series and parallel circuits: measurement of voltage-current relation and verification by
calculation - plotting the instantaneous power against time
3. Calibration of the single phase energy meter by direct loading at various power factors
4. Measurement of power in the three phase circuit using single, two and three wattmeters for balanced
load and for three and four wire system
5. Determination of the equivalent circuit of transformer by open and short circuit test - calculation of
efficiency and regulation at various loads and power factors.
6. Determination of the regulation of alternator by emf and mmf methods
7. Starting the cage induction motor using star-delta switch and plotting the performance characteristics
8. Conducting the no load and blocked rotor test on cage induction motor - determining equivalent circuit
and calculating torque-slip characteristics
9. a) Plotting OCC of DC shunt generator at rated speed - determining the critical resistance. b)
Conducting load test on DC shunt generator and plotting external characteristics - deducing internal
characteristics
10. Conducting load test on DC series motor and plotting the performance characteristics
11. Study of single phase capacitor start and capacitor run induction motors - plotting speed - voltage
relation of single phase fan motor
Sessional work assessment
Lab Practicals and Record = 30
Test = 20
Total marks = 50
University evaluation will be for 100 marks of which 70 marks are allotted for writing the
procedure/formulae/sample calculation details, preparing the circuit diagram/algorithm/flow chart, conduct
of experiment, tabulation, plotting of required graphs, results, inference etc., as per the requirement of the
lab experiments, 20 marks for the viva-voce and 10 marks for the lab record.
Note: Duly certified lab record must be submitted at the time of examination.




KANNUR UNIVERSITY
FACULTY OF ENGINEERING
Curricula, Scheme of Examinations & Syllabus for
Semesters V & VI of B.Tech. Degree Programme in
MECHANICAL ENGINEERING
with effect from 2007 Admissions
FIFTH SEMESTER
Hours/Week
Sessional Marks
University Examination
Code
Subject
L
T
P/D
Hrs
Marks
2K6 ME 501
Engineering Mathematics IV
2
1
-
50
3
100
2K6 ME 502
Environmental Engineering and Disaster Management
2
-
-
50
3
100
2K6 ME 503
Mechanics of Machinery
2
-
-
50
3
100
2K6 ME 504
Thermal Engineering
2
-
-
50
3
100
2K6 ME 505
CAD/CAM/CAE
2
1
-
50
3
100
2K6 ME 506
Machine Tools
2
-
-
50
3
100
2K6 ME 507(P)
Production Engg Lab II
-
-
3
50
3
100
2K6 ME 508(P)
Thermal Engineering Lab
-
-
3
50
3
100
TOTAL
12
2
6
400
-
800
SIXTH SEMESTER
Hours/Week
Sessional Marks
University Examination
Code
Subject
L
T
P/D
Hrs
Marks
2K6 ME 601
Economics and Business
Management
2
-
-
50
3
100
2K6 ME 602
Dynamics of Machinery
2
-
-
50
3
100
2K6 ME 603
Heat and Mass Transfer
2
-
-
50
3
100
2K6 ME 604
Advances in Manufacturing Engineering
2
1
-
50
3
100
2K6 ME 605
Operations Research
2
1
-
50
3
100
2K6 ME 606
Elective I
2
-
-
50
3
100
2K6 ME 607(P)
Heat Transfer Lab
-
-
3
50
3
100
2K6 ME 608(P)
CAD/CAM/CAE Lab
-
-
3
50
3
100
TOTAL
12
2
6
400
-
800
Elective I
ELECTIVE-1
2K6 ME 606(A): Numerical Methods
2K6 ME 606(B): Mechatronics
2K6 ME 606(C): CNC Programming
2K6 ME 606(D): Tool Engineering and Design
2K6 ME 606(E): Vibration and Noise Control
2K6 ME 501: ENGINEERING MATHEMATICS –IV
3hrs.lectureand1hourtutorialperweek
Module I: Probability distributions (13 hours)
Random variables-Probability distributions - binomial distribution –Poisson distribution-normal distribution –Mean, variance and Moment generating function -Poisson process - chebyshev’s theorem- Geometric Distribution-Uniform Distribution, Gamma distribution, Beta Distribution, Exponential Distribution and Hyper-Geometric Distributions.
Module II: Statistical inference (13hours)
Population and Sample-Sampling Distributions of Mean and Variance-Point Estimation-Interval Estimation -Null Hypotheses and Significance tests-Hypotheses concerning one mean- Confidence Intervals of mean and variance -Estimation of Variances-Hypotheses concerning one variance-Hypotheses concerning two variance- Chi square test as test of goodness of fit.
Module III (Series solutions of differential equations (13hours)
Power series method of solving ordinary differential equations - series solution of Bessel's equation – Recurrence formula for Jn(x)-expansions for J0 and J1 – value of J1/2- generating function for Jn(x) - Orthogonality of Bessel functions - Legendre’s equation – series solution of legendary’s differential equation -Rodrigues formula-Legendre Polynomials – Generating function for Pn(x)- Recurrence formulae for Pn(x) -Orthogonality of Legendre polynomials
Module IV Quadratic forms and Fourier transforms (13 hours)
Quadratic forms - Matrix associated with a quadratic form - Technique of Diagonalization using row and column transformations on the matrix - Definite, Semidefinite and Indefinite forms - their identification using the Eigen values of the matrix of the quadratic form.
Fourier Transform-Properties of Fourier Transforms-Linearity property-Change of scale property-shifting properties –Modulation property-Transform of the Derivative-simple problems-Fourier Cosine transform-Fourier Sine Transform.
University Exami
nation Pattern
Q I 8
– short answer type questions of 5 marks, 2 from each module.
Q II 2wer any one.
- questions of 15 marks each from module I with choice to ans
Q II2
I- questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V 2
- questions of 15 marks each from module IV with choice toanswer any one.
Text Book
1. Johnson RA, Miller & Freund’s Probability and Statistics for Engineers, Prentice Hall of India (For Module I and II only) Reference Books 1. Wylie CR & Barrett LC, Advanced Engineering Mathematics, Mc Graw Hill 2. Kreyszig E, advanced Engineering Mathematics, John Wiley. 3. NP Bali & Manish Goyal, A Text book of Engineering Mathematics, Laxmi Publications 4. Dr.B.S. Grewal, Higher Engineering Mathematics, Khanna Publishers
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 502 ENVIRONMENTAL ENGINEERING & DISASTER MANAGEMENT
3hrs.lectureand1hourtutorialperweek
MODULE I (12 HOURS)
Multidisciplinary nature of Environmental studies – Definition – scope and importance – need for public awareness
Natural resources – renewable and non-renewable resources – natural resources – forest resources - water resources
Mineral resources – food resources – energy resources – Land resources – use, overuse and misuse of these resources with appropriate case studies to substantiate – effect on the environment – role of individual in conservation of natural resources – equitable use of resources for sustainable lifestyle.
MODULE II (12 HOURS)
Ecosystem – concept – structure and function – producers, consumers & decomposers – energy flow in the ecosystem- Ecological successive food chains - food webs ( all in brief)
Ecological pyramids – introduction, types and characteristic features, structure and function of forest, grassland, desert and acquatic ecosystems ( ponds, lakes, streams, rivers, oceans and estuaries) Biodiversity and its conservation – Introduction – definition : genetic species and ecosystem diversity – Biogeographical classification of India – value of biodiversity – consumptive and productive use, social, ethical, aesthetic and option values – biodiversity at global, national and local levels – india as a mega-diversity nation – hot spots of biodiversity – threats to biodiversity : habitat loss, poaching of wildlife, man-wildlife conflicts – endangered and endemic species of India – conservation of biodiversity : In-situ and Ex-situ conservation of biodiversity.
MODULE III ( 13 HOURS)
Environmental Pollution – Definition – causes - effects and control measures of : Air Pollution – water Pollution – soil Pollution – marine Pollution – noise Pollution – thermal Pollution – Nuclear hazards .
Solid waste management – causes, effects and control measures of urban and industrial wastes – Role of an individual in preventing Pollution – Environmental Protection Act – Prevention and control of air and water Pollution – Wildlife Protection Act – Forest Conservation Act – Issues involved in Enforcement of Environmental Legislation – Public awareness.
Disaster Management – Principles of disaster management – nature and extent of disasters – natural disasters , hazards, risks and vulnerabilities – man-made disasters – chemical, industrial, nuclear and fire. – preparedness nd mitigation measures for various hazards – financing relief expenditure – legal aspects - post disaster relief – voluntary agencies and community participation at various stages of disaster management – rehabilitation programmes.
MODULE IV ( 10 HOURS)
Social Issues and the Environment – From unsustainable to sustainable development – urban problems related to energy – water conservation, rain water harvesting , watershed management – resettlement and rehabilitation of people ; its problems and concerns, case studies – environmental ethics : Issues and possible solutions – climate change, global warming, acid rain, ozone layer depletion, nuclear accidents and holocaust. Case studies – waste land reclamation – consumerism and waste products.
Human population and the environment – Population growth, variations among nations – population explosion – Family welfare programmes – Environment and human health – Pollution hazards, sanitation and health – Human rights for a clean environment – value education – HIV/AIDS – social concern – Women and Child welfare – role of Information Technology in environment and human health – Case studies.
FIELD WORK ( 5 HOURS)
• Visit to a local area to document environmental assets – river / forest / grassland / hill / mountain
• Visit to local polluted site – urban / rural / industrial / agricultural
• Study of common plants, insects , birds
• Study of simple ecosystems – pond , river , hill slopes , etc.
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
Text book
1. Clarke. R.S. Marine Pollution. Clanderson Oress Oxford.`
2. Mhaskar A.K. Matter Hazardous. Techno-Science Publications.
3. Townsend. C., Harper. J. and Michael Begon, Essential of Ecology. Blackwell Science.
4. S. Deswal & A . Deswal, A Basic Course in Environmental Studies, Dhanpat Rai & Co
5. Environmental Studies – Dr. B . S. Chauhan, University Science Press.
6. Kurien Joseph & R. Nagendran, Essentials of Environmental Studies, Pearson Education.
7. Trivedi. R.K. and Goel. P.K. Introduction to air pollution. Techno-Science Publications.
Reference Books
1. Agarwal.K.C. Environmental biology. Nidi Publ.Ltd. Bikaner.
2. Bharucha erach, Biodiversity of India, Mapin Publishing Pvt.Ltd.,.
3. Brunner,R.C.. Hazardous Waste Incineration. McGraw Hill Inc..
4. Cunningham W.P. , Cooper T.H., Gorhani E. & Hepworth M.T. Environmental Encyclopedia
,Jaico Publ.House ,.
5. De A.K. Environmental Chemistry.Wiley Eastern Ltd.
6. Hawkins R.E. Encyclopediaof Indian Natural History, Bombay Natural History Society ,.
7. Heywood V.H. & Watson R.T.. Global Biodiversity Assessment. Cambridge Univ. Press.
8. Jadhav H. & Bhosale V.M.. Environmental Protection and Laws. Himalaya Pub. House,
9. Odum E.P. Fundamentals of Ecology W.B. Saunders Co..
10. Rao M.N. & Datta A.K. Waste Water Treatment. Oxford & IBH Publ. Co. Pvt. Ltd..
11. Sharma B.K.. Environmental Chemistry Goel Publ. House, Meerut
12. Trivedi R.K., Handbook of Environmental Laws, Rules, Guidelines, Compliances and Standards,
Vol.I & II.Enviro Media.
13. Wagner K.D. Environmental Management. W.B. Saunders Co.
2K6ME 503: MECHANICS OF MACHINERY
3hrs.lectureand1hourtutorialperweek
Module I (13 hours)
Introduction to mechanism and machines – Kinematic Pairs – Kinematic Chains and Linkages – Structure and Kinematic Diagrams - Various mechanism – Kinematic inversion - degree of freedom – Displacement analysis – Relative motion – Velocity and Acceleration analysis – Instantaneous centre – Complex number method – Mechanical advantage – Relative acceleration – Coriolis acceleration – graphical and analytical methods – Topics from path curvature theory – Fixed and moving centroides – Inflection points and inflection circle – Euler Savary equation.
Module II (13 hours)
Force analysis of machinery – static and dynamic force analysis of plane motion mechanisms – analytical, graphical and complex method – principle of superposition – matrix method – method of virtual work – complex number method.
Module III (14 hours)
Gears– Gear Tooth Action - The Law of Gearing - Involute spur gears – involutometry – spur gear details – interference – gear standardization – backlash –internal gear – cycloidal gear – non standard gear – theory and details of bevel, helical and worm gearing – Gear trains – simple and compound gear trains – planetary trains – solution of planetary gear train problems – applications – Force analysis in spur – helical – bevel and worm gearing.
Module IV (12 hours)
Kinematic synthesis – tasks of kinematic synthesis – type and dimensional synthesis – graphical synthesis for motion – path and prescribed timing – function generator – overlay method – analytical synthesis techniques – complex number modelling – Freudenstien’s equation – loop closure equation technique – one case study in synthesis of mechanism.
Text Book
1. A.Ghosh & A.K.Mallik, Kinematic Analysis and Synthesis of Mechanism, Affiliated
East West Press.
2. H.Hamilton,Mabie & Charles F.Reinholtz , Mechanism and dynamics of Machinery,
John Wiley & sons.
Reference Books:
1. J.E.Shigley & J.J.Uicker Jr.,Theory of Machines and Mechanisms, Mc Graw Hill.
2. S.S Rattan, Theory of Machines, Tata Mc Graw Hill.
3. V.P. Singh, Theory of Machines, Dhanpat Rai and Co.
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 504 THERMAL ENGINEERING
3hrs.lectureand1hourtutorialperweek
Module I (14 hours)
Internal combustion engines - classification - four stroke and two stroke engines - spark ignition and compression ignition engines - valve timing diagram - thermodynamic analysis of air standard cycles - Otto, diesel and duel combustion cycles - engine testing - performance and characteristics of constant speed and variable speed engines - heat balance test - Morse test - retardation test - actual engine cycles - effect of dissociation - variable specific heats and heat losses - scavenging - objectives - effects and methods
Module II (13 hours)
Systems and components of IC engines - fuel systems - ignition systems - cooling - starting - lubrication - governing of IC engines - supercharging of SI and CI engines - turbocharging - exhaust emissions of IC engines - alternate potential engines - free piston engine - Wankel engine and stratified charged engine - automotive transmission system and its components
Module III (12 hours)
Combustion in IC engines - flame propagation - normal and abnormal combustion - detonation - pre ignition - after burning - HUCR - fuel rating - additives in petrol - combustion chambers of SI engines - combustion in CI engines - phase of normal combustion - diesel knock - effect of engine variables on diesel knock - cetane number - additives in diesel - combustion chambers of CI engines
Module IV (13 hours)
Gas turbine plants - open and closed cycles - thermodynamic cycles - regeneration - reheating - intercooling - efficiency and performance of gas turbines - rotary compressors - analysis - centrifugal and axial flow compressors - combustion chambers of gas turbines - cylindrical - annular and industrial type combustion chamber design - combustion intensity - combustion efficiency - pressure loss combustion process and stability loop - axial flow turbines - elementary and vortex theories - design of nozzles and blades for turbines - limiting factors in turbine design
Text Book and References
1. Rogowsky, “Elements of Internal Combustion Engines”, Tata McGraw Hill
2. Gill, Smith & Ziurys, “Fundamentals of Internal Combustion Engines”, Oxford and IBH
3. Maleev, “Internal Combustion Engine Theory and Design” McGraw Hill
4. Judge, “Modern Petrol Engines,” Chapman & Hall
5. Benson & Whitehouse, “Internal Combustion Engines” Vol. I & II, Pergamon press
6. Mathur & Mehta, “Thermodynamics and Heat Power Engineering”, Vol. I & II
7. Cohen & Rogers, “Gas Turbine Theory,” Longmans
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 505 CAD/CAM/CAE
3hrs.lectureand1hourtutorialperweek
Module I (13 hours)
Fundamentals of CAD: Introduction: Design Process: Application of computers in design: Creating manufacturing database: benefits of CAD. Computer Hardware; Graphic input devices; display devices; Graphics output devices; Central processing unit (CPU) Geometric modelling- wireframe and solid modelling, engineering analysis-FEM, design review and evaluation, automated drafting, design data base, softwares used in CAD, data exchange between CAD and CAM. Fundamentals of CAM: Definition of automation, levels of automation, high volume discrete parts production, Detroit type of automation, transfer machines, analysis of automated flow lines, assembly
machines, flow line balancing, line balancing.
Module II (14 hours)
NC/CNC Machine Tools; NC machine tools- basic components, coordinate systems; features of NC machine tools. Computer Numerical Control: basic theory of numerical control, advantages of NC, open and closed loop system, information flow and control theory, classification of CNC machine tools, position control and continuous path control, principles of displacement measurement, digital linear and rotary displacement transducer, analog displacement measuring system. CNC part programming: Manual programming, work piece modelling and computer aided part programming, canned cycles, Computer assisted Part Programming languages, programming in APT.
Module III (13 hours)
Basic concepts of Robotics: Introduction, basic structure of Robots, resolution, accuracy, and repeatability. Classification and structure of Robotic systems: PTP and CP systems, control loops of robotic systems, types of robots Drives and Control systems: hydraulic systems, DC servo motors, control approaches of Robots. Applications of Robots. Programming: manual teaching, lead – through teaching, programming languages. Sensors and Intelligent Robots: introduction to Robotic sensors, vision systems, range detectors, force and torque sensors.
Module IV (12 hours)
Advanced concepts in automation: direct numerical control,Adaptive control, Group Technology (GT): Part families; part classification and coding system: Group technology machine cells: Advantages of GT. Computer Aided Process Planning: Introduction and
benefits of CAPP. Types of CAPP systems, machinability data selection systems in CAPP. CAE, CIM, FMS, computer integrated manufacturing
Text Book and References
1. Groover & Zimmers “CAD/CAM” PHI
2. Rdhakrishnan “CAD/CAM”
3 Mikell P. Groover, “Automation, Production Systems and Computer Aided Manufacturing”, Prentice Hall, 1980
4 Mechatronics : HMT (TMH)
5 CNC Programming made easy: B.K.Jha, Vikas Publishing House
6 Robot Technology – Fundamental: James G Keramas, Vikas Thomson Learning
7 Computer Integrated Design and Manufacturing by D.D. Bedworth, M.RHenderson &
P.M. Wolfe, Tata MCGraw Hill Pub. Co.
8.CAD/CAM-theoryandPracticebyZeidIbraham,TataMcGrawHillPubCo
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 506: MACHINE TOOLS
3hrs.lectureand1hourtutorialperweek
MODULE I (13 hours)
Basic Concepts of Machine Tools: General requirements of machine tools- tool- work motions on lathe, milling, drilling, shaping, slotting, planing and grinding machines- cutting speeds and feeds- estimation of machining time.
Kinematics of Machine Tools: Selection of range of speeds and feeds- layout of speeds- graphical representation of speed and structure diagram- ray diagram for machine tool gear boxes
Machine Tool Drive: Stepped and step less regulation of speeds- feed and speed mechanisms in lathe, milling and drilling machines- gauging of components.
MODULE II (13 hours)
Cutting Tools: Geometry of cutting tools and tool nomenclature- single point and multipoint cutting tools- tools used for turning, milling, drilling and broaching- tool materials and their properties- grinding wheels and their selection. Production Lathes: Turret lathes- tools and attachments- operations and tools layout- automatic screw machine
Metal Cutting: Mechanics of chip formation- types of chips- orthogonal and oblique cutting- velocity relationships- cutting forces and factors affecting cutting forces- cutting force and power analysis- thermal aspects of machining- cutting fluids and their selection.
MODULE III (13 hours)
Machinability and Tool Life: Tool wear and tool life- tool life equations- tool life specifications and criteria- effect of machining parameters on tool life- variables affecting machinability -Economics of machining: Selection of optimum machining conditions- machine law and tool law
Jigs and fixtures: Basic principles- elements of jigs and fixtures- design principles common to jigs and fixtures.
MODULE IV (13 hours)
Press working: Different types of presses- principles of operation and selection- computation of capacities tonnage- center of pressure- cutting operations- shear action in die cutting operations- compound and progressive dies
Text Book and References
1. HMT, Production Technology, Tata McGraw Hill
2. Ghosh & Mallik, Manufacturing Science, Affiliated East-West Press
3. Juneja & Sekhon, Fundamentals of Metal Cutting and Machine Tools, Wiley Eastern
4. Sharma P C, A Text book of Production Engineering, S Chand & Company
5. ASTME, Fundamentals of Tool Design, Prentice Hall of India
6. Bhattacharya A, Metal Cutting: Theory and Practice, Central Book Publishers
7. Boothroyd, Fundamentals of Metal Machining and Machine Tools, McGraw Hill
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 507(P): PRODUCTION ENGG LAB II
3hrs.practicalperweek
Introduction: limits and fits - horizontal milling machine - vertical milling machine - shaping machine - slotting machine - surface, centreless and cylindrical grinding - spindle drives - milling cutters - indexing head - simple, compound, differential and angular indexing - grinding wheel - drilling - reaming - tool layout
Introduction
Exercises:
1. Multi-start thread
2. Square thread
3. Eccentric turning
4. Exercise on limits and fits
5. Internal thread
6. Spur gear
7. Helical gear by simple and differential indexing
8. Surface, slot and keyway milling
9. Shaper exercise on cube with V-groove, slot and guide ways
10. Grinding
11. Tool grinding
Text Books and References
1. HMT, Production Technology, Tata McGraw Hill
2. ASTME, Tool Engineer’s Handbook
3. Burghardt, Asilered & Anderson, Machine Tool Operations I & II, McGraw Hill
4. Chapman W.A.J., Workshop Technology: Part 2., Viva Low Priced Student Edition
Rao R.V., Metal Cutting and Machine Tools, S K Kataria & Sons
Sessional Work Assessment
Laboratory practical and record – 35 marks
Tests – 15 marks
Total – 50 marks
2K6ME 508(P): THERMAL ENGINEERING LAB
3hrs.practicalperweek
1. Study of systems and components of petrol and diesel engines
2. Study of automotive parts
3. Study of air compressors, blower and fan
4. Study of boilers and turbines
5. Performance test on refrigeration plant
6. Performance test on air conditioning plant
7. Performance test on boilers
8. Determination of flash and fire points of oils
9. Determination of viscosity of oils
10. Determination of calorific value of fuels
11. Valve timing diagram on petrol and diesel engines
12. Load test on single cylinder four stroke diesel engine
13. Load test on twin cylinder four stroke diesel engine
14. Load test on four cylinder four stroke diesel engine
15. Load test on single cylinder four stroke petrol engine
16 Load test on twin cylinder four stroke petrol engine
17. Load test on four cylinder four stroke petrol engine
18. Load test on two stroke petrol engine
19. Heat balance test on petrol engine
20. Heat balance test on diesel engine
21. Cooling curve test on petrol engine
22. Cooling curve test on diesel engine
23. Morse test on petrol engine
24. Morse test on diesel engine
25. Retardation test on diesel engine
26. Retardation test on petrol engine
27. Variable speed test on petrol engine
28. Variable speed test on diesel engine
29. Performance test on rotary air compressor
30. Performance test on air blower
12 experiments should be done as a minimum depending up on the lab facility.
Text Book and References
1. Rogowsky, “Elements of Internal Combustion Engines”, Tata McGraw Hill
2 Gill, Smith & Ziurys, “Fundamentals of Internal Combustion Engines”, Oxford and IBH
3 Maleev, “Internal Combustion Engine Theory and Design” McGraw Hill
Sessional Work Assessment
Laboratory practical and record – 35 marks
Tests – 15 marks
Total – 50 marks
2K6 ME 601: ECONOMICS AND BUSINESS MANAGEMENT
3hrs.lectureand1hourtutorialperweek
Module 1 (12 hours)
Definition of economics – nature and scope of economic science – nature and scope of managerial economics – central problems of an economy – scarcity and choice - opportunity cost – objectives of business firms – forms of business – proprietorship – partnership – joint stock company – co-operative organisation – state enterprise
Module II (14 hours)
Consumption – wants – characteristics of wants – law of diminishing marginal utility – demand – law of demand – elasticity of demand – types of elasticity – factors determining elasticity – measurement – its significance in business – demand forecasting – methods of demand forecasting – supply – law of supply elasticity of supply
Module III (14 hours)
Production – factors of production – features of factors of production – division of labour – production function – Cobb – Douglas production function – production possibility curve – isoquants – marginal rate of technical substitution – properties of isoquants – law of variable proportions – returns to scale – isocost line – least cost combination of factors – expansion path – technical and economic efficiency – linear programming – graphical method – economies of large scale production
Module IV (12 hours)
Market structures and price determination – perfect competition – monopoly – monopolistic competition – oligopoly – kinked demand curve – money and banking – nature and functions of money – money market and capital market – commercial banks – functions – central banking functions – methods of credit control.
Text Book and References
1. Varshney R.L & Maheshwari K.L, Managerial Economics, S Chand & company Ltd.
2. Dwivedi D.N, Managerial Economics, Vikas Publishing House Pvt Ltd.
3. Dewett K.K, Modern Economic Theory, S Chand & Company Ltd.
4. Barthwal A.R, Industrial Economics, New Age International Publishers
Benga T.R & Sharma S.C, Industrial Organisation And Engineering Economics,
5. Benga T.R & Sharma S.C, Industrial Organisation And Engineering Economics, Khanna Publishing
6. Ahuja H.L, Modern Micro Economics – Theory and Applications, S Chand & Company Ltd.
7. Koutsoyiannis A, Modern Microeconomics, Macmillan Press Ltd.
8. Joel Dean, Managerial Economics, Prentice – Hall of India Pvt. Ltd.
9. Dewett. K.K. & Verma J.D, Elementary Economic Theory, S Chand & Company Ltd.
Jhingan M.L, Macro Economic Theory, Vrinda Publications Pvt. Ltd.
10. Jhingan M.L, Macro Economic Theory, Vrinda Publications Pvt. Ltd.
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 602: DYNAMICS OF MACHINERY
3hrs.lectureand1hourtutorialperweek
Module I (13 hours)
Introduction to mechanical vibration – free and forced - response of single degree of freedom - linear systems – coulomb damping – support excitation – vibration isolation – whirling of shafts – two degree of freedom systems – coordinate transformations – coupling - natural coordinates – beat phenomenon – undamped vibration - vibration absorbers.
Module II (13 hours)
Multi degree of freedom systems – matrix formulation – influence coefficients – Eigen value problem – expansion theorem – modal analysis – solution methods – general response of discrete linear systems – self exited vibrations – criterion for stability - instability caused by friction – instability in oil film lubricated bearings – galloping of transmission lines – introduction to nonlinear vibration – introduction to random vibration.
Module III (13 hours)
Cam design – cam and follower types – displacement diagrams – Advanced cam profile techniques – cam profile synthesis – graphical and analytical methods – Gyroscope-gyroscopic couple – stability of two wheeler – four wheeler – gyroscopic effect:on aeroplane – steering, rolling and pitching of ships.
Module IV (13 hours)
Flywheel analysis– turning moment diagram – flywheel design – flywheel applications - balancing - static and dynamic balancing – balancing of masses rotating on several planes – balancing of reciprocating masses –balancing of mult-icylinder engines – balancing machines.
Text Book
1 W. T. Thomson, Theory of vibration with applications, Prentice Hall
2. J. P. Den Hartog, Mechanical vibrations, Mc Graw Hill.
3. J.E.Shigley & J.J.Uicker Jr.,Theory of Machines and Mechanisms, Mc Graw Hill.
References
1. S.S Rattan, Theory of Machines, Tata Mc Graw Hill.
2. V.P. Singh, Theory of Machines, Dhanpat Rai and Co..
3. Erdman A.G & Sandor G.N., Mechanism Design: Analysis and Synthesis
4. Leonard Meirovitch, Elements of vibration analysis, Mc Graw Hill
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 603: HEAT AND MASS TRANSFER
3hrs.lectureand1hourtutorialperweek
Module I (16 hrs)
Basic Concepts of Thermodynamics and Heat Transfer. Heat and Other Forms of Energy. Heat Transfer Mechanisms. Simultaneous Heat Transfer Mechanisms.
Heat Conduction: Heat Conduction Equation .One-Dimensional Heat Conduction Equation. General Heat Conduction Equation. Boundary and Initial Conditions. Solution of Steady One-Dimensional Heat Conduction Problems. Heat Generation in a Solid. Variables Thermal Conductivity. Steady Heat Conduction in Plane Walls. Heat Conduction in Cylinders and Spheres. Critical Radius of Insulation. Heat Transfer from Finned Surfaces Transient Heat Conduction. Transient Heat Conduction in Large Plane Walls, Long Cylinders and Spheres. Transient Heat Conduction in Semi-Infinite Solids. Numerical Methods in Heat Conduction. Finite Difference Formulation of Differential Equations. One-Dimensional Steady Heat Conduction. Transient Heat Conduction.
Module 2 (12 hrs)
Convective Heat Transfer: Physical Mechanism of Forced Convection. Velocity Boundary Layer. Thermal Boundary Layer. Empirical relation in forced convection. Flow Over a Flat Plates. Flow across Cylinders and Spheres. Flow in Tubes. Physical Mechanism of Natural Convection. Empirical relation in free convection. Natural Convection over Surfaces, inside Enclosures, and from Finned Surfaces. Combined Natural and Forced Convection.
Module 3 (12 hrs)
Boiling and Condensation: Boiling Heat Transfer. Pool Boiling. Flow Boiling. Critical Heat Flux (CHF). Condensation Heat Transfer. Film Condensation. Film Condensation inside Horizontal Tubes
Heat Exchangers: Type of Heat Exchangers. Temperature Distribution – Overall heat transfer coefficient, Heat Exchange Analysis – LMTD Method and NTU Method.
Module 4 (12 hrs)
Radiation Heat Transfer: Introduction to Physical mechanism. Radiation properties. Thermal Radiation. Blackbody Radiation. Solar Radiation. Radiation laws. The View Factor. Radiation Heat Transfer, Radiation Shields.
Mass Transfer: Introduction. Mass Diffusion. Fick’s law of diffusion. Boundary Conditions. Steady Mass Diffusion through a wall. Mass Convection
Text Book and References
1 Yunus A. Cengel., “Heat Transfer – A practical approach”, Second Edition, Tata
McGraw-Hill 2. Incropera. F.P.and Dewitt.D.P. “Introduction to Heat Transfer”, John Wiley and Sons 3. Holman, J.P. “Heat Transfer”, McGraw-Hill Book Co., Inc., New York, 6th Edn.4. Sachdeva, S.C., “Fundamentals of Engineering Heat & Mass Transfer”, Wiley Eastern
Ltd., New Delhi
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 604: ADVANCES IN MANUFACTURING ENGINEERING
3hrs.lectureand1hourtutorialperweek
Module I (13 hours)
Computer technology - introduction - CPU - types of memory - input/output devices - computer programming - operating the computer system - mini/micro computers and programmable controllers - computer aided design - fundamentals of CAD - the design process - application of computers for design - manufacturing data base - computer graphics - software configuration - constructing the geometry - transformations - data base structure and content - wire frame and solid models
Module II (13 hours)
Numerical control - basic components of NC systems - NC coordinate systems - motion control system - application of numerical control - NC part programming - punched tape - tape coding and format - manual part programming - computer assisted part programming - APT language - NC programming with interactive graphics
Module III (13 hours)
Manufacturing systems - development of manufacturing system - components of FMS - FMS work station - Job coding and classification - group technology - benefits of FMS - tools and tooling - machining centres - head indexers - pallets - fixtures - work handling equipments - system storage - automated guided vehicles - industrial robots - programming of robots - assembly & inspection
Module IV (13 hours)
Flexible manufacturing system management - FMS control software - manning of FMS - tool management - controlling precision - simulation and analysis of FMS - approaches to modelling for FMS - network simulation - simulation procedure - FMS design - economics of FMS - artificial intelligence
.
.
Text Book and References
1. Groover M.P. “Automation, Production Systems and Computer Integrated Manufacturing”, Prentice Hall of India
2. Groover, Emory & Zimmers, “CAD/CAM Computer Aided Design and Manufacturing”, Prentice Hall of India
3. Joseph Talavage & Hannam, “Flexible Manufacturing Systems in Practice”, Marcel Dekker Inc.
4. Kant Vajpayee, “Principles of Computer Integrated Manufacturing”, Prentice Hall of India
5. Yoram Koren, “Computer Control of Manufacturing Systems”, McGraw, Hill Book Company
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 605: OPERATIONS RESEARCH
3hrs.lectureand1hourtutorialperweek
Module I: Linear algebra (13 hours)
Vectors - vector space and Euclidean space - vector operations - matrix operations - unit vector - sum vector - linear dependence - bases - spanning set - rank - simultaneous equations - basic solutions - point sets - lines and hyper planes - linear inequalities - convex sets - extreme points - fundamental theorem of linear programming
Module II: Linear programming (13 hours)
Statement of the LP problem - slack and surplus variables - basic feasible solutions - reduction of a feasible solution to basic feasible solution - artificial variables - optimality conditions - unbounded solutions - Charnes’ M method - two phase method - degeneracy - duality
Module III: Transportation, assignment and game problems (13 hours)
Transportation problem - coefficient matrix and its properties - basic set of column vectors - linear combination of basic vectors - tableau format - stepping stone algorithm - UV method - inequality constraints - degeneracy in transportation problems - assignment problem as a maximally degenerate transportation problem - Köning’s method - rectangular zero sum games - von Neuman’s theorem - saddle points - pure and mixed strategies - formulation of the primal and dual LP problem for fixed strategies - dominance - graphical solutions
Module IV: Queuing theory (13 hours)
Basic structure of queuing models - exponential and Poisson distributions - birth and death processes - queuing models based on Poisson inputs and exponential service times - basic model with constant arrival rate and service rate - finite queue - limited source queue models involving non-exponential distributions - single service model with Poisson arrival and any service time distribution - Poisson arrival with constant service time - Poisson arrival and Erlang service times - priority disciplines - dynamic programming - Bellman’s principle of optimality - formulation and solution of simple problems
Text Book
1. Hadley G, Linear Programming, Addison Wesley
2. Hillier & Lieberman, Operations Research, John Wiley
3. Ravindran, Solberg & Phillips, Operations Research, John Wiley
References
1. Saskrieni, Yaspen & Friedman, Operations Research: Methods and Problems, Wiley Toppen
2. Wagner, Principles of Operations Research, Prentice Hall of India
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 606(A): NUMERICAL METHODS
3hrs.lectureand1hourtutorialperweek
MODULE I: (14 hours) Systems of equations Introduction to mathematical modeling- algorithms-convergence – rate, order of convergence- errors in numerical algorithms-Finding roots of polynomial equations- bisection method- method of false position-Newton-Raphson method- fixed point iteration-Secant method –Convergence of these methods-Gauss elimination method for systems of linear equation-pivoting strategies-LU decomposition – Iterative techniques for linear systems-Jacobi, Gauss Seidel method-Conjugate gradient method-Non-linear systems of equations-Newton’s method –application problems-power method for the determination of Eigen values.
MODULE II (12 hours). Interpolation Lagrange form of the interpolating polynomial-Newton’s form of the interpolating polynomial- divided differences- finite difference operators- Newton’s forward and backward interpolations- Stirling’s interpolation formula-errors of interpolation formulae- Cubic spline interpolation-curve fitting- linear regression.
MODULE III: (13 hours)
Numerical differentiation and integration Numerical differentiation- differential formulae in the case of equally spaced points- Richardson extrapolation- Numerical integration –Newton-Cotes quadrature- trapezoidal and Simpson’s rules- Gaussian integration-error analysis- Initial value problems of ordinary differential equations- Euler’s method-Taylor methods.
MODULE IV: (13 hours) Numerical solution of ordinary differential equations
Runge-Kutta methods –multistep methods-Adam-Bashforth and Adam-Moulton method-Predictor-Corrector schemes-Milne’s method-Solution of boundary value problems in ordinary differential equations-finite difference methods for solving two dimensional Laplace equation for a rectangular region- finite difference method of solving heat equation and wave equation with given initial and boundary condition.
Text Book
1.Froberg C.E., Introduction to Numerical Analysis, Addison Wesley
2.Gerald C.F., Applied Numerical Analysis, Addison Wesley
3.Hildebrand F.B., Introduction to Numerical Analysis, T.M.H.
4.James M.L., Smith C.M. & Wolford J.C., Applied Numerical Methods for Digital
Computation, Harper & Row
5.Mathew J.H., Numerical Methods for Mathematics, Science and Engineering, P.H.I
References
1.Bradie Brian, A Friendly Introduction to Numerical Analysis, Pearson Education.
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 606(B): MECHATRONICS
3hrs.lectureand1hourtutorialperweek
MODULE I: (11 hours) Introduction to mechatronics-sensors and transducers-signal conditioning-pneumatic and hydraulic systems-mechanical and electrical systems.
MODULE II: (11 hours) System modeling-mathematical models-mechanical, electrical, fluid and thermal system building blocks-system models- dynamic response of systems- first and second order systems-modeling dynamic systems-systems transfer functions-frequency response-stability.
MODULE III: (15 hours) Controllers Closed loop controllers-continuous and discrete processes-proportional, derivative and integral controls-PID controller-digital controllers-controller tuning-adaptive control.
MODULE IV: (15 hours) Digital circuitsMicro controllers and micro processors-digital logic circuits-micro controller architecture and programming-programmable logic controllers
Text Book
1. Bolton W., Mechatronics: Electronic Control Systems in Mechanical and Electrical
Engineering, Addison Wesley Longman Limited
References
1. Dorf R.C. & Bishop R.H., Modern Control Systems, Addison Wesley
2. Krishna Kant, Computer Based Industrial Control, Prentice Hall of Indian Private Limited
3. HMT Limited, Mechatronics, Tata McGraw Hill Publishing Company Limited
4. Herbert Taub & Donald Schilling, Digital Integrated Electronics, McGraw Hill InternationalEditions
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 606(C): CNC PROGRAMMING
3hrs.lectureand1hourtutorialperweek
Module I (13hrs)
An Introduction to Numerical Control Machinery: The History of NC, CNC Machines, Input Media, Binary Numbers, Tape Formats, Objectives of Numerical Control, Applications in Industry
Numerical Control Systems: Components, Types of Control Systems, Servomechanisms, Loop Systems, The Cartesian, Coordinate System, Positive and Negative Movement, Positioning Systems, Setting the Machine Origin, Dimensioning
Process Planning and Tool Selection: Process Planning, Tooling for Numerical Control, Tooling for Hole Operations, Milling Cutters Special Inserted Cutters, Speed and Feeds, Tool Changes, Automatic Tool Changers, Tool Storage, Tool Length and Tool Length Offset
Module II (13hrs)
Programming Coordinates: Hole Operations, Milling Operations, Mixing Absolute and Incremental Positioning, Metric Coordinates
Two Axis Programming: Introduction, Parts of a CNC Program, Word Address Format, Absolute Positioning, Incremental Positioning, Milling and Drilling Examples
Three Axis Programming: Introduction, A Programming Task Using Three Axes, Other G-Codes Used in CNC Programming, Using an Indexer, Programming Examples
Math for Numerical Control Programming: Using Trigonometry for Cutter Offsets, Milling and Lathe examples
Linear and Circular Interpolation: Linear Interpolation, Circular Interpolation,
Cutter Diameter Compensation: Definitions and Codes, Program Example, Special Considerations, Fine Tuning with Cutter Diameter Compensation
Module III (13hrs)
Do Loops and Subprograms: Do Loops, Subprograms, Calling a Subprogram, Subroutines for Cutter Diameter Compensation, Nested Loops
Advanced CNC Features: Mirror Imaging, Polar Rotation, Helical Interpolation
The Numerical Control Lathe: Lathe Bed Design, Axis Movement, Tool holders and Tool Changing, Spindle Speeds, Feed rates, Machine Origin and Work Coordinate Systems, Quick setters
Programming CNC Turning Machines: Machine Reference Point, Diameter vs. Radius Programming, Turning and Facing, Taper Turning, Circular Interpolation, Drilling, Threading
Module IV(13hrs)
Use of Computers in Numerical Control Programming: Offline Programming Terminals, Computer-Assisted Programming, Computer-Aided Programming Languages, CAD/CAM Systems, Solid Modeling Systems
The Future of Numerical Control: NC in Prototype and Job Shops, CNC in Manufacturing, Employment Opportunities in NC
Text Book and References
1. Lynch; Computer Numerical Machining, 1992, McGraw-Hill
2 Stanton, George C. Bridgeport Heidenhain CNC Mill: Programming & Operating
Instructions.
3 Valentino, J.V. & Goldenberg, J. (2003). Introduction to computer numerical control (CNC)
(3rd Ed.). Upper Saddle River, NJ: Prentice Hal
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 606(D): TOOL ENGINEERING AND DESIGN
MODULE I: (13 hours) Design of chips forming tools
3hrs.lectureand1hourtutorialperweek
Single point tools-tool geometry-tool materials-milling cutters-drills and reamers-grinding wheels-tipped tools-design of tool holders and boring bars-vibration damping of boring bars-form tools-influence of cutting parameters on cutting force and power-cutting power estimation in turning, milling and drilling.
MODULE II: (13 hours) Press working tools
Power presses-die cutting operations-centre of pressure-punch and die size and press tonnage calculations-scrap-strip layout-compound and progressive dies-die design for simple components-drawing dies-blank development-press tonnage estimation-blank holding pressure-multiple draws-draw dies for simple shells.
MODULE III: (13 hours) Design of fixture
Elements of fixture-standard work holding devices-principles of location and clamping-plain and concentric location-clamping elements-quick acting clamps-design and sketching of fixtures for milling of simple components.
MODULE IV: (13 hours) Design of jigs
Jigs for drilling and reaming-types of jigs-guide bushings-indexing jigs-design and sketching of jigs for simple jobs
Text Book and References
1. Kempster M.H.A., "An Introduction to Jig and Tool Design", ELBS
2. ASTME, Fundamentals of Tool Design
3. Grant H.E., "Jigs and Fixtures - Non Standard Clamping Devices", Tata McGraw Hill
4. Goroshkin A.K., "Jigs and Fixtures Hand Book", MIR Publishers
5. Wilson & Holt, "Hand book of Fixture Design", McGraw Hill
6. Colving & Haas, "Jigs and Fixtures - A Reference Book", McGraw Hill
7. Cole B., "Tool Design", Taraporevala
8. Donaldson, Lecain & Goold, "Tool Design", Tata McGraw Hill
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6ME 606(E): VIBRATION AND NOISE CONTROL
3hrs.lectureand1hourtutorialperweek
MODULE I: (13 hours)
Introduction to mechanical vibration-free and forced response of single degree of freedom linear systems-Coulomb damping-support excitation-vibration isolation-whirling of shafts-measurement of vibration-accelerometer-seismometer.
MODULE II: (13 hours)
Two degree of freedom systems-coordinate transformations-coupling natural coordinates-beat phenomenon-undamped vibration absorbers-multi degree of freedom systems-matrix formulation-influence coefficients-Eigen value problem-expansion theorems-model analysis-solution methods-general methods of discrete linear systems.
MODULE III: (13 hours)
Vibration of continuous systems-exact methods-boundary value problem-Eigen value problem-axial vibration of rods-bending vibration of bars-Rayleigh’s quotient-response of systems by modal analysis-energy of continuous systems-general elastic waves-formulation and decoupling of equilibrium equations-approximate methods-different methods like Rayleigh’s energy method, Rayleigh-Ritz method and Holzer’s method
MODULE IV: (13 hours)
Self excited vibrations-criterion of stability-instability caused by friction-instability in oil film lubricated bearings-galloping of transmission lines-introduction to nonlinear vibration-introduction to random vibration-stationary random process-probability density functions-auto correlation function-power spectral density function-noise-sound level meter scale-psychological scale-equivalent sound level-noise and loss of hearing-psychological effects of noise-noise exposure limits-noise control-control at the source-control along the path-control at the receive
Text Book
1. Thomson W.T., Theory of Vibration with Applications, Prentice Hall
2. Den Hartog J.P., Mechanical Vibrations, McGraw Hill, Self excited vibration, Module IV
3. Sanders M.S. & McCormick E.J., Human Factors in Engineering and Design, McGraw Hill, Noise, Module IV
References
1. Leonard Meirovitch, Elements of Vibration Analysis, McGraw Hill
2. Amitabha Ghosh & Asok Kumar Mallik, Theory of Mechanisms and Machines, Affiliated East-West Press
3. Kinsler L.E. & Fray A.R., Fundamentals of Acoustics, John Wiley, Module IV
4. Beranek L.L., Noise and Vibration Control, McGraw Hill, Module IV
5. Love AEH, Treatise on Mathematical Theory of Elasticity, Dover, Elastic Waves, Module III
6. Constable JER & Constable K.M., Principles and Practice of Sound Insulation, Isaac Pitman & Sons
University Examination Pattern
Q I – 8 short answer type questions of 5 marks, 2 from each module.
Q II- 2 questions of 15 marks each from module I with choice to answer any one.
Q III- 2 questions of 15 marks each from module II with choice to answer any one.
Q IV- 2 questions of 15 marks each from module III with choice to answer any one.
Q V- 2 questions of 15 marks each from module IV with choice to answer any one.
Sessional Work Assessment
Tests (2X15) – 30 marks
Assignments (2X10) – 20 marks
Total – 50 marks
2K6 ME 607(P) HEAT TRANSFER LAB
3hrs.practicalsperweek
List of experiments
1. Performance study on parallel flow and counter flow Heat exchanger.
2. Performance study on Shell and tube Heat exchanger.
3. Measurement of emissivity.
4. Measurement of solar radiation.
5. Determination of thermal conductivity of metal rod.
6. Experiment on forced convection heat transfer.
7. Experiment on unsteady state conduction.
8. Experiment on drop wise and film wise condensation.
9. Measurement of critical heat flux.
10. Experiment on natural convection heat transfer.
11. Experiment on boiling heat transfer.
12. Determination of thermal resistance of composite wall
13. Determination of Stefan Boltzman constant.
14. Determination of thermal conductivity of asbestos powder.
15. Determination of effectiveness of fin.
Text Book and References
1 Yunus A. Cengel., “Heat Transfer – A practical approach”, Second Edition, Tata
McGraw-Hill 2. Incropera. F.P.and Dewitt.D.P. “Introduction to Heat Transfer”, John Wiley and Sons 3. Holman, J.P. “Heat Transfer”, McGraw-Hill Book Co., Inc., New York, 6th Edn.4. Sachdeva, S.C., “Fundamentals of Engineering Heat & Mass Transfer”, Wiley Eastern
Ltd., New Delhi
Sessional Work Assessment
Laboratory practical and record – 35 marks
Tests – 15 marks
Total – 50 marks
2K6 ME 608(P) CAD/CAM/CAE LAB
3hrs.practicalsperweek
1. Exercise on solid modeling using available software packages- Concepts of computer aided modeling, design, analysis and manufacturing- Survey of various available software for the above areas– introduction to computer graphics, curves and surface generation, sweep, revolve, loft, extrude, filleting, chamfer, splines etc. Scaling and rotation transformation using commercial solid modeling packages: 2 D drafting and 3 D modeling.
2. Assembly and mechanical design – assembling of various parts and tolerance analysis – synthesis and design of mechanisms - four bar chain, cam and follower, two stroke and four stroke engines – 3D modeling, assembling, animation and analysis using available software packages.
3. Computer aided manufacturing – part programming fundamentals – hands on training in computer controlled machining operations – part programming, simulation and operation on CNC lathe and CNC milling machines- modeling, simulation and programme generation using software packages.
4. Exercises on Finite Element Analysis –introduction to FEM -1 D, 2 D,3 D elements – shape function- processing –boundary conditions, structured and free mesh generation – analysis – linear and nonlinear analysis – static and dynamic analysis – post processing – display , animation, extraction of nodal data –exercises on heat conduction and elasticity using available FEM packages.]
5. Programming of Industrial Robots – introduction to robotics – structure, workspace analysis and various components- actuators – sensors – encoders – end effectors – applications –hands on training on industrial robots – manual and programmed path planning. Programming of Robots using available software packages.
6. Computer aided inspection and quality control- introduction to CMM- classification – structures – components – familiarity with measurement software packages and its modules –demonstration of the capability of coordinate measuring machines using a sample component eg.- engine block.
7. concepts of reverse engineering and rapid prototyping technology
Text Book and References
1. Rogers D.F. & Adams J.A., “Mathematical Elements for Computer Graphics”, McGraw Hill
2. Rogers David F., “Procedural Elements for Computer Graphics”, McGraw Hill
3. Cook, Robert Davis et al., “Concepts and Applications of Finite Element Analysis”, John Wiley
4. Koren Yoram, “Computer Control of Manufacturing Systems”, McGraw Hill
5. Kundra Rao & Tewari, “Numerical Control and Computer Aided Manufacturing”, Tata McGraw Hill
6. Ramamurthy V., “Computer Aided Mechanical Design”, Tata McGraw Hill
7. Fu K.S., Gonzalez R.C. & Lee C.S.G., “Robotics: Control, Sensing, Vision and Intelligence”, McGraw Hill
8. Koren Yoram, “Robotics for Engineers”, McGraw Hill
9. Bosch J.A., “Coordinate Measuring Machines and Systems”, Marcel Decker Inc
Sessional Work Assessment
Laboratory practical and record – 35 marks
Tests – 15 marks
Total – 50 marks